Sunday, September 23, 2012

Smoke-smoke go away

There are good points about living in Central Washington the biggest is all the sun we get.  So, of coarse there is a down side and that is it is very dry here.   We had a huge storm roll through about two weeks ago.   During that time we were hit with a hundred lightning strikes, I know there were a lot but didn't count them, so will take the word of anyone who's job it is to count lightning strikes.
Those stikes started 80 fires, in other words our whole mountain area is on fire and here in the valley we are getting smoke.  
I always read the description of fall as the smell of smoke in the air.  I am sure this is not what they were thinking.

Saturday, September 22, 2012

Simple things

Making hair bows might seem simple to those that are handy at such things.  I needed something simple to do while my strength comes back, so I thought about how happy hair bows make the grand daughters.  I never seem to find time to make them and now that I have the time I thought I would share a post that was shared on EverythingSewing by Ann a wonderful bow maker.   Then I found these pictures of some bows done by my friend Jerry after she had followed Ann's directions.  So if you need a little help in making bows, these instructions are just perfect.

Ann, you may have created a monster!!! :rotflo: 
Image

I had just a bit of the candy corn ribbon left after using it in the back tie pillowcase dress that was orange with white dots, so I thought I would see if I could turn it into a facsimlie of Ann's bow. It worked! I still need to practice getting my center knot tight and wrapped tightly around the bow, but for my first practice run, I'm very pleased. :D

Making hair bows



1. Cut ribbon to 29 inches. This makes approximately a 4-inch bow. After you make a few this size, you can make larger or smaller bows simply by cutting longer or shorter lengths of ribbon.
Image

2. Fold the ribbon in half lengthwise and finger press this crease.
Image

3. Turn up cut ends approximately 3 inches and finger press crease. These will be the tails of the bow and can be cut later to exactly how you want them.
Image
Image

4. Fold ribbon in half again and finger press crease.
Image

Now to fold the bow. 

5. Starting on left-hand side, bring 1st fold to 2nd fold at a 45 degree angle.
Image

6. Bring 3rd crease on top or 1st crease at a 45 degree angle.
Image

7. Bring 4th crease UNDER 3rd crease at a 45 degree angle.
Image

8. Bring final crease on top of previous crease at a 45 degree angle.
Image

9. Bring threaded needle from back to the front through in the center through all creases.


To crease the bow.

10. Take thread over the top of the bow and behind and with thread dangling, start to pull the thread to make the crease in the bow. 

11. Wrap thread around the bow several times, shaping loops as you pull thread tight and secure thread in the back.

You have just tied the bow. You may have to pull and shape the loops at this point, but as you make more bows, you will see just which loops need a little coaxing.
Image

The center of the bow.

12. I use a ¼ ribbon for the center. I do NOT buy ¼ ribbon to match the bow. I simply cut a 6-inch strip of remaining ribbon to approximately ¼ inch and use the same method as the tales to seal the cut side. 
Image

12. Tie a loose knot in the center of the ribbon – don’t pull it very tight.
Image

13. Put a dot of hot glue on the center of ribbon and attach the loose knot on the hot glue.
Image

14. Hot glue the clip to the back of the ribbon.
Image

15. Pull one end of center tie over the clip and hot glue and trim.
Image
Image

16. Pull the remaining end over the tie and hot glue and trim.
Image
Image

17. Cut ends of tales the way you want them to look and apply Frey Check lightly to the cut ends.
Image

18. If ribbon seems limp, I spray with spray starch and shape as the starch dries.

With a little practice, these bows are adorable and get so easy to tie. 

Hints: I use 1 ½ inch ribbon which to me looks the best. 
Printed ribbon is best to learn with as you can tell exactly which side is which.
I use hot glue but fabric glue can also be used. It just does not “grab” like hot glue does and also does not dry immediately like hot glue.


S