Saturday, April 11, 2015

ADD A FLOPPY HAT- A RE-POST

I hope I am getting you excited to get in the sewing room and whip something up.
With spring time and summer not far behind, it is a perfect time to make some hats to go with every outfit. That will keep the sun off of our precious girls.
I really love making this hat:
Because summer is coming I am re-posting, to give you time to make those summer hats.

Floppy Hat Pattern

Step One: Measure the child’s head at angle hat will be worn (Picture 1). This one measures 19 inches.
picture 1
Step Two: Cut a 2 inch wide band of knit fabric or ribbing the length of child’s head .The more stretch, the easier it is to sew. I just used a t-shirt knit. Sew the short ends together with 3/8-inch seam to create the hatband. Try on. It should not be too snug or fall off the child’s head. It should be comfortable. (Picture 2).
picture 2
Step Three: Take the measurement of the child’s head (circumference) and divide it by 6.28. This will give you the radius. For example, 19 inches divided by 6.28 equals 3.02548 inches. I rounded this up to 3.1 inches. Do not round down or the hat will be too small. Find the measurement of the radius on a compass (in this case 3.1 inches) and draw a circle on your pattern material (I use interfacing) (Picture 3).
picture 3
Step Four: Leaving the point of the compass in same spot, move the pencil point out
2 ¼ inch and draw another circle (Picture 4). This becomes the brim pattern.
picture 4
Step Five: With point of compass still in place, move pencil point out 1 inch and draw a third circle. This will be the hat crown pattern (Picture 5). This is what you end up with (Picture 6).
picture 5 picture 6
Step Six: At this point you should trace the two inner circles (which is the brim pattern) onto separate interfacing so the brim and crown each have their own pattern.

Step Seven: Next, cut out one crown and two brim pieces. The brim pieces should be interfaced with lightweight fusible or non-fusible interfacing (I like fusible, see Picture 7). Set the brim pieces aside.
picture 7
Step Eight: Divide the band and crown pieces into eight equal parts with pins (Picture 8). Pin right sides together at pin marks (Picture 9). Sew with ¼ inch seam stretching band to fit. If your band doesn’t stretch enough you can gather the crown slightly with your fingers as you sew (Picture 9a).
picture 8 picture 9 picture 9a
Step Nine: Turn right side out and try on (Picture 10).
picture 10
Step Ten: Put brim pieces right sides together and sew ¼ inch seam along outer circle. Trim and clip onto seam and turn right side out (Picture 11).
picture 11
Step Eleven: Divide brim (inner circle) and band into eight equal parts with pins. Pin the two together at pin marks (Picture 12). Sew with ¼ inch seam with band on top (Picture 13).
picture 12 picture 13
Step Twelve: Zigzag or serge this raw edge (Picture 14).
picture 14
Step Thirteen: You can cover the seam with flexible trim or rickrack as I did here (Picture 15). I just used fabric glue but you can sew it on if you want (sometimes I omit step 13 all together).
picture 15
Step Fourteen: Try on hat. Brim can be turned up in the front or left down. Embellish as you please.
picture 16 picture 17

6 comments:

  1. Wow Nonie, I never knew it was that easy to make little hats!! Yes, you have given me some inspiration to do something else now!

    ReplyDelete
  2. Beautiful. really Nice job there.

    ReplyDelete
  3. This comment has been removed by a blog administrator.

    ReplyDelete
  4. My granddaughters would look so cute in a sweet hat like these. Maybe I can measure their heads when they visit tomorrow.

    ReplyDelete
    Replies
    1. Sherry, I think little girls look so cute in this hat, hope you share a picture.

      Delete